Quantity: 1, Year: 2004, Type: Servo Scroll ex-fineline, BR:5.

Quantity: 6

1x Tuftco Enhanced Loop Graphics tufting machine. Year 1998. 4 meter, 1/10th gauge, 6 roll, servo split roller rainbow on each side, ELG drive system. Hydra shifter needle bar shifters. Currently tufting 144 inches. CM4.

1x Tuftco Enhanced Loop tufting machine, Year 1998. 4 meter, 1/10th gauge, with 6 rolls, split roller rainbow on front side, split roll loop. Hydra shifter needle bar shifter. Servo cloth feed. Currently tufting 144 inches. CM5.

1x Tuftco Enhanced Loop Graphics tufting machine. Year 1997. 4 meter, 1/10th gauge 6 roll, servo split roller rainbow on each side. Hydra shifter needle bar shifters. Servo cloth feed, ELG drive system and loop pile. Currently tufting 144 inches. CM8.

2x Tuftco Enhanced Loop Graphics tufting machine. Year 1996. 4 meter, 1/10th gauge 6 roll, servo split roller rainbow on each side. Hydra shifter needle bar shifters. ELG drive system, pile loop. Currently tufting 144 inches. CM4.

1x Tuftco Enhanced Loop Graphics tufting machine. Year 1999. 4 meter, 5/64th gauge 6 roll, servo split roller rainbow on rear, pile loop. Four roll, full-width yarn feed in front. Servo needle bar shifters. Servo cloth feed. Currently tufting 144 inches. CM12.

Quantity: 1, Year: 1993, 4 meter , Currently tufting 146” width. Dual 5” yarn feed rollers, Tuftco Hydra shifters, inverter, mending frame and rollup.
Model 110165693-S.

Quantity: 1, Year: 2002. 5″, front side yarnfeed. Tufting 179″ wide. Includes Inverter, Tight end detector, Creel, Mending Frame and
3 roll pivot dump rollup with 12” dia x 200” rollers.

Quantity: 1, Year: 2003, 4 Meter, 1/10th gauge Tuftco servo scroll, With 120 servo driven clutch assemblies. Servo cloth feed and servo shifter. Front side yarn feed with tube bank. 12 inch pattern repeat. Currently tufting 144. CM3. There is no creel, mending frame or rollup with this machine. It has been out of service for 3 years.
Machine has 1,620 tubes/holes so it was designed to make 410cm tufting. Buyer can add needles, loopers and needle plates, they are modular in all the machines and can be added easily by a tufting mechanic. Approx cost to do is USD 2000

Quantity: 1, Year: 2000, 4 meter. With 120 servo driven clutch assemblies. Servo cloth feed and servo shifter. Front side yarn feed with tube bank. 12 inch pattern repeat. Currently tufting 144 inches. CM1. Loaded into two 40HC containers.
Machine has 1,620 tubes/holes so it was designed to make 410cm tufting. Buyer can add needles, loopers and needle plates, they are modular in all the machines and can be added easily by a tufting mechanic. Approx cost to do is USD 2000.

Quantity: 1, Year: Approx 1999‎, 15 FT, 1/8 gauge.
With 144 clutch, 3 pile height scroll attachment.
In-line shifting needle bar with 24 inch ‎cam shifter.
CMC Command Performance control system.‎
Currently tufting 12 ft width.
Gearboxes on cloth and yarn feed
This machine is in excellent condition.‎ it in production.
Delivery in 2×40′ HC Container
NOTE: ADD $4,000 to make it 4 Meter.‎
Machine is moved to warehouse by professional technicians.
Buyer can add loopers, finger plates and needles to widen and tuft 410cm width.

Quantity: 1, Year: 1989, MP, Mech, Working width: 5m, Straight‎, LH‎, Type: 52040589, Feed rolls: 4, Speed RPM: 800‎, Dtex Range: 1950/3900‎, Pile Height: 8 – 25‎, Creel: Creel‎, Pre winder: yes‎, Inspection: yes‎, Roll Up: 3 rolls, Yarn Feed: Front, Stitch Rate: 15-65‎
Good condition. Height can be modified to 40 mm (tuftco high speed) good machine.
WITH Primary Backing UNWINDER
1 x 40 FT HC container.
When the customer wants extra:
inspection + roll-up = EXTRA EUR 5.000 loaded in 2x 40′ container.
Pile-height :
40 mm is %100 very easy to do on the machine, 45 mm after some adjustment can be done, 50 mm, the machine can not do, Machine was doing Grass before, 8000 dtex is easy and machine can do, only some needles should be changed.
Machine can easily be modified to GRASS (has 2 driven motors, necessary to pull that heavy yarn.)
Less needles are needed: 5/16” in case of 5/32”
New needles are required to change to Gauge 5/16″ for 8000 dtex, number of required needles depend on if customer wants to use the machine in 4m width or 5m width.
Changing Gauge to 5/16 is easy and can be done by taking out half the Tufting needles.

Quantity: 1, Cut & Loop Sample Machine. 2 pile height clutch yarn feed front and rear. Front has standard loop pile looper and rear has looper with fixed clip. Currently tufting 16 inches wide but can tuft up to 36 inches by adding gauge parts.

Quantity: 1, Year: 1994, Servo, DSN – hydra multiroll graphics, Working width: 5m, Staggered, RH, Type: 110204694-S, Feed rolls: 4, Speed RPM: 750‎, Dtex range: 1800/2500‎, Pile Height: 4 – 12‎, Creel: no creel‎, Pre winder: yes‎, Inspection: no‎, Roll Up: 2 rolls, Yarn Feed: Front+back, Stitch Rate: 15-75‎
Good condition
WITH Primary Backing UNWINDER
1 x 40 FT HC container.
When the customer wants extra:
inspection + roll-up = EXTRA EUR 5.000 loaded in 2x 40′ container.

Quantity: 1, Year: 1997, Servo, Working width: 5m‎, Feed rolls: 4, Straight, Speed RPM: 1000, LH, Type: 42041296-L‎, Dtex Range:1950/3900‎, Pile Height: 4 – 20‎, Creel: no creel‎, Pre winder: yes‎, Inspection: no‎, Roll Up: no
Machine can Tuft Artificial Grass ( Turf )
Good condition, height can be modified to higher pile by changing excentrics
WITH Primary Backing UNWINDER
1 x 40 FT HC container.
When the customer wants extra:
Inspection + roll-up = EXTRA EUR 5.000 loaded in 2x 40′ container