Quantity: 3, Year: 2000, IN(INCH): 8, Out(INCH): 6, Spindle: 208, POT DIA: 19, POT HEIGHT: 37 CM , MACHINE LENGHT : : 26,5 MT 90 CM, MACHINE WIDTH: 90cm
Note:
1-The machines can 2 ply assembly wind and 2 ply twist at same time
2-In and Out bobbin sizes can set as below
Bobbin Feeding: 6″, Bobbin Exit: 6
Bobbin Feeding: 8″, Bobbin Exit: 6
Bobbin Feeding: 10″, Bobbin Exit: 6
3- Each machines has 2 air splicers
4- Each machines has OHTC system
5- All machine take up tubes are cones 4° 20’ and it can chance to cylindrical

Machines are not compact twisting

Quantity: 2, Year: 2002, 192 head, 8 inch feeding, 6 inch delivery, 195 cm diameter, Invertor.

Quantity: 1, Year: 1997, Spindles: 160, 6 INCH, POT DIAMETER 190 MM.

Quantity: 1
Year: 2000
Double twist twister for spun yarn
192 spindles (8+8 spindles per section)
Informator for programming work data
Dual control (allows different twisting and speed on each side)
Possibility of dividing the machine into three groups on each side of the machine, which allows working up to three twists and three different speeds on each side of the fan.
Yarn guide movement is common by each side of the machine
1 individual rotating motor in each spindle
Start/stop button on each spindle
Electronic sensor/yarn presence probe w/ automatic spindle stop in case of breakage
Pneumatic yarn feeding
Fedding bobbin up to 10″ coming from assembly winder
Device for forming of soft packages, if desired for dyeing
Output pachages of 6 inches (152mm of wire winding)
Possibility of forming conical bobbins 4º 20; 5°57, or cylindrical bobbins as desire
Lateral reserve of yarn for weaving preparation
Automatic package lifting with blockage aplet
Top creedle with supports for empty cones or full packages
MAGITEX traveling blower with box for centralized discharge with timer
Longitudinal tape with micros for emergency stop of the machine in case of need
Inverter speed drives for electronic introduction of torsion and spindle speed
RPM 9,000 (18,000 double twist)
Minimum TPM 80
In excellent maintnance condition and functioning.
Machine lengths 21940mm
Voltage 380v.3c.50hz.
NOTE; Machine professionally dismantled, and moved to warehouse.

Quantity: 1, Year: 1997, 192 spindles, Bauart 5.20, single drive
feeding 2×6 ” Duo Pot or 8 / 10 inch to assembly winder, basket diameter 180 mm, gauge 220 mm, exit 6 inch (152 mm) – conicity 4°20′, pneumatic threading, reserve yarn, Magitex

Quantity: 3, Year: 1997, Spindle: 216, 8’ in, 6’ out,

Quantity: 4
Year: 1997-1998
2x machines feeding 7 inch delevry 6 inch, machines have 132 spindles each
2x machines feeding 8 inch delevry 6 inch, machines have 220 spindles each

Quantity: 3, Year: 1990, 180 positions, take-up cylindrical and conical, max. dia. 176 mm, S or Z twist
Height (tube) is 197 mm and max. dia. is 176 mm.‎Height inside. pot is 180 mm, Gauge is 15 sections each 12 twisting positions.‎

Quantity: 1, Year: 2002, 192 head, 8 inch feeding, 6 inch delivery
Big pot 8 inch x 19 cm diameter, Original invertor, Excellent condition

Quantity: 2, Year: 2014, SINGLE BOBIN -10”, FEED-8” OUT, 210 Spindles.

Quantity: 1, Year 1982, 36 spindles, two sided, 6” delivery, 6” (4°20) take up
New motor and inverter recently fitted (I think it was 2020), and very little work done since new motor.
Excellent working order and condition throughout
Only selling as we don’t have an assembly winder to suit, so most of the twisting is going on the larger VTS-06S we use.
Machine wired in and running.

Quantity: 1, Year: 2011, Type VTS-07-0, Bauart 6.10, 120 spindles, free ballon, Speed until 11.000 tpm = 22.000 twist-turns, Pot-high 235 mm, spindle-pitch 296 m, Turns 74-1516 t/m, Length 21,20 m, width 900 mm, Pots for assembling cones 10“, dia. 180 mm or 2 x 5“ cones, Take up for tubes 6“ conical and cylindrical, Very good condition.

Quantity: 5, Year: 1997, 176 mesh, 8 inch input 6 inch output.