BLENDING:

5x HOLLINGSWORTH 60″ WIDE FEED HOPPERS
TYPE: BFC-1500, 60 inch wide feed Aprons, Weigh Pans Empty Into a 40″ Wide Blending Conveyor, Year 1993

1x HUMP MAGNET METAL DETECTOR
Year 1990

1x SIGNAL MIXING BIN
100 inch wide, 250 inch long, Moving lattice steel floor for emptying, Inclined Lattice, Year 2006

1x TEMAFA MIXED FIBER BALE OPENER
60 inches wide, Main Cylinder with claw teeth, Feed roller with claw teeth, Double take off rollers with Claw teeth, YEAR 1998

1x ARGUS METAL DETECTOR
Year 1998

5.5 METER DILO LINE – YEAR OF MANUFACTURE 1998

CARDING:
1x SPINNBAU 3.0 M WIDE CARD FEEDER
With Air Box – Condenser, Vibra Feed Chute Feed with Feed Rolls

1x SPINNBAU WEIGHING TABLE
Type ME-Z

1x SPINNBAU SINGLE CYLINDER CARD
3 meters wide, Double Doffer, with Feed Rolls, Breast With Worker and Stripper, Main Cylinder with 5 Sets of Workers and Strippers, Double Doffers, Take down Aprons to Deliver Batt to Entry Apron of Crosslapper, Year 1998

CROSSLAPPER:

1x AUTEFA CROSSLAPPER
Model “Topliner”, Type 96.48, 3 meter Input, 6.0 meter Wide output, onto Floor Apron, Year 2012

NEEDLING:

1x DILO FEED, Model VE.4-60, Year 1998

1x DILO PRE-NEEDLE LOOM
Type: Di-Loom OD-1-S-60, 1 Board Down stroke, Compressive Batt Feed Type CBF-60T, 6.0 m Wide, Year 1998

1x DILO 4-ROLL DRAFTING UNIT
Type VE4/60, 6.0 meter Wide, Year 1998

1x DILO “QUAD-PUNCH” NEEDLE LOOM
2 Boards Down and 2 Boards Up Stroke, Type Di-Loom OUGIIS/55, 5.5m Wide, Year 1998
(1) Graseby (Goring-Kerr) Metal Detector
(1) Entec 4-Roll Stretching (Drafting) Unit
(1) Entec Inclined Pin Tenter
5.5 Meter Working Width, Vertical Chain Return, with Electronic Edge Guiding and Rotary Brush, Pinning On Device

1x HITRACH/ENTEC DRYER
with 10 Heaters and 2 Edge Heaters, with Circulating Fans, Hood and Exhaust Fans

1x PERKNS 4 ROLLER CALENDAR
Oile Heated with Thermal Oil Boiler

1x ENTEC VERTICAL ACCUMULATOR
with 144 Yards Linear Storage Capacity, NDC Thickness Scanner and Controller

1x ENTEC, FULL WIDTH LIGHTED INSPECTION FRAME
with Pull Rolls, with Edge Trim, and Automatic Edge Guiding on to (1) Entec 2 Roll Surface Drive, Automatic Tube Feeder, Take-Up Winder with Automatic Doffing

1x MACHADYNE ROLL-WRAPPING UNIT
with Traversing Wrap Unit, To Holding Table for Finished Rolls

1x RANGE DRIVE AND CONTROLS
To Operate and Monitor Entire Line, Type Di-Loom UD-II-SB 45, 4.5m Wide, Year 2006, Year 2013

ADDITIONAL EQUIPMENT:

1x P & S PICKER 48”
12 Bar Bear Claw

1x LAROCHE LOW MELT FINE OPENER
60” Width, Pin Beater Roll

1x THIBEAU CARD
Model 15P5 CA6, Single Cylinder, Double Doffer, 2.5 Meter Width

1x ASSELIN CROSSLAPPER
4.5 Meter Laydown, W/Floor Apron

1x VFW HOPPER FEED SYSTEM

1x THIBEAU CARD
Model 15P5, 2.5 Meter Width, Double Cylinder, Single Doffer

1x ASSELIN CROSSLAPPER
Type 390, 4.5 Meter Laydown, W/Floor Apron

1x FEHRER TACKER
Model NL9/S, 3.9 Meter, Year 1983

1x FEHRER NEEDLELOOM
Model NL21, 4 Meter Width, Year 1983

1x Argus Metal Detector

1x ASSELIN CROSSLAPPER
Type 390, 4.5 Meter Laydown, W/Floor Apron

1x FEHRER TACKER
Model NL9/S, 4 Meter, Year 1994

1x FEHRER NEEDLELOOM
Model NL21, 4 Meter Width, Year 1994

1x BOMBI THREE-ROLLER NONWOVEN CALENDER
Type CAL/3C/5.8, 3 Roll, Working width 5800 mm, Max roller width 6100 mm, Roller Diameter 800mm, Pressure approx. 25 tons, Oil Heated, Year: 2007