Quantity: 1, Year: 1996, w.w. 2.20 m, Gas, 2 chambers, 3 passages.

Quantity: 1, Year: 2003, Composed of: High entry with centering unit E+L KF2020.
TMT Foulard completely in Stainless Steel. Model F2Sv. Power 5Kw. Two Rollers 2.000 mm width. Box with 3 + 3 rollers with fabric capacity 4 mt. J-Box accumulator.
SANTEX Dryer Model SANTASOFT. Year 2008. 2 Chambers. Steam Heated. Exit with E+L ELSMART and Spanders E+L ELSPREADER and Folder.

Quantity: 1, Year: 1997, Working width: 2’400 mm, Max temperature: 160°C, 3 Chambers, Tensionless shrinkage and relaxation drier, Steam heated system, PLEVA moisture control system, Vibrating device, Steam injection, Overfeed device, SANTAVISION control panel modified to operate with a keypad and mouse.

Quantity: 1, Year: 2010, Mod. Enairgy, Roll width 3800, Entry with steamer, Gas heated.

Quantity: 1, Year: 2012, Type: RBY K2 H2600 , Working width 2450 mm, For knitting fabrics, Entry with spirals scroll rollers and centralizing device
E+L overfeeders, extended entry with steamer, horizontal pin chain, 2 chambers, steam heating, cooling zone, exit with J-box and rolling inspection machine, Touch screen control programmer with inverters with steam boiler DECONINCK WANSON year of construction 2012, pressure 12 Bar, burner gas heating.

Quantity: 1, Year: 2000, Type LFC 151-3500 , 400VAC 45A 50Hz, working width 3500mm, main fuse 63A, drum Ø 1350mm used for thermo-fixation, laminating and transfer-printing. Including double accumulator ateliers Belmont type BTM03 year: 2000 and beating brush, pressure roller to use while laminating. Heated by a thermal oil tank Thermopac Wanson Type TPC 300 LNE, 349kW, 32.2 mVk, 400V 50Hz 9kW working temperature 210°C.

Quantity: 1, Year: 2006, USA Origin, Width 240cm, 8 chamber, 1 padder, Horizontal chain, Pin chain, Oil heated, Running for knitting and woven.

Quantity: 1, Year: 1993, BCPL-SW model, Useful width 2300 mm
With:
Main Power 440 VAC – 60 Hz, Fuel: Natural gas
Main Board with GE FANUC SERIES 90-30 General Electric PLC and VDC drives for machine synchronization motors.
2 Drying fields (drums and relaxed), each section has 2 natural gas burners with flame controllers and Honeywell pyrometers. The relax section conveys the material on a Nomex mat which is automatically kept centered.
Cooling area with output to folder and lint capture with discharge to air filters.
2 Hot air extractors connected to an outlet duct.
Front, rear and mid-section control buttons.

Quantity: 1, Year: 1990, Working width 2200 mm.
Equipped with:
High entry with mechanical tensioner
FABCON impregnation pad with stainless steel sizing tank, 2 rollers covered in rubber, in vertical position with pneumatic pressure.
BIANCO electronic straightener with 4 optical readers.
Control station with edge guide fingers, needle threaders, overfeeder, chain width control device in the input field and vertical needle chain.
2 Heat setting fields of 9 mt length each, equipped with chain width control device, gas burner, fan and chimney.
Cooling field with fan and fireplace.
Exit of the machine with fabric reel for rolls with 50 cm maximum diameter.
Device for rolls of fabric on easel type “A” with maximum diameter of 150 cm.

Quantity: 1, Year: 1989, Model: AMV, No. Chambers: 4, No. passages: 3, Length of the chambers: 15 meter, Heating system: Thermo Oil, Roller width: 2.400 mm, Max. working width: 2.200 mm, No. conveyor belts: 3.

Quantity: 1, Year: 1995, Model: AMV, No. Chambers: 4, No. passages: 3, Length of the chambers: 15 meter, Heating system: Steam, Roller width: 2.400 mm, Max. working width: 2.200 mm, No. conveyor belts: 3.

QUANTITY: 1, YEAR: 2003, MOD.FLAT 2000 , WW.2000MM, 4 CHAMBERS ‎FOR TOTAL OVEN 16 METERS, GAS HEATED WITH TWO BURNERS PER CHAMBER, INLET BY ‎OVERFEEDING ELECTRONIC FROM 0 UP TO +50%, VERTICAL CHAINS PINS AND ‎ANTIDEPINNING, WEFTSTRIGHTNER E+L AT INLET CYLINDERS TYPE 6 READING HEADS, ‎FOULARD TMT TWO CYLINDERS STAINLESS STEEL CONSTRUCTION , EXIT BY COOLING ‎FOLDER AND SMALL ROLLS, MACHINE LIKE NEW ONE VERY FEW USES STILL INSTALLED IN ‎MILL.‎

QUANTITY: 1, TYPE 6 CHAMBERS GAS HEATED, VERTICAL CHAINS PINS , ‎SUITABLE TO DRY HIGHT PILE FABRICS AFTER RESINGS APPLICATION ON BACK SIDE, WW ‎‎3200MM, EXIT BY FOLDER. MACHINE STILL INSTALLED ON MILL.‎

QUANTITY: 1, WW 2000MM, 4 CHAMBERS GAS , TMT ‎FOULARD AT INLET 3 CYLINDERS, VERTICAL CHAINS, OVERFEEDING, AC MOTORIZATION ‎TOUCH SCREEN COMPUTER, COOLING ,FOLDER AND SMAL ROLL AT EXIT STILL INSTALLED IN ‎MILL

Quantity: 1
Year: 2006
Type: Redevo 4DF2 K2200
Working width up to 220 cm
Composed of:
High entry with CORINO spreading and centering device type FLC4, UNITECH padder face roller width 240 cm, UNITECH coating head type Coat 220 with face roller width 240 cm, Stenter entry with 3-finger uncrawlers and IR edge feelers, Overfeeding, vertical combined pin and clip chain with 4 m long entry field, Steaming, selvedge glueing, IR selvedge pre-drying before entering the drying fields, 2 gas heated fields with WEISHAUPT burners type WG20N/1-C ZM-LN (35-200 kW), Exit with cooling field, selvedge trimming and suction, Plaiter exit and ascending roll exit, Dimensions length 19,55 x width 6,7 x height 3 m, Voltage is 380 V, 50 Hz
This machine has worked as project development and has around 300 running hours. The reason for these low hours is that the machine was supplied to a textile research center.

Quantity: 1, Year: 2007, Working width: 2’400 mm, Max temperature: 160°C, 3 Chambers, Tensionless shrinkage and relaxation drier, Steam heated system, PLEVA moisture control system, Vibrating device, Steam injection, Overfeed device, SANTAVISION MP370 touch screen controller.

Quantity: 1 ,Year: 2000, Type TERMA mod.340/05 , width 3400 mm., 5 compartments, horizontal pins chain, gas heating, Mahlo weftstraightener in input and weft control device in output, no Padder.

Quantity: 1,Model TDR- 1,8-T Tumbler
Date of mfg 5-15-99 , Voltage 480 3/phase
Working width of 1,800 mm or 72”
Machines are heated by gas / using Maxon gas heat exchangers
The machine is currently installed inline with two separate independent units which can be operated together or individually.
The first machine serial no. 98039 is built with 3 Heating Bays, has its own electrical control cabinets and a variable speed controller cloth winding unit.
The unit has its own dust filtration system.
The second machine serial no. 98040 is built with 2 Heating Bays, has its own electrical control cabinets and fabric flat fold plaiter.
This unit is also equipped with its own dust filtration system.

Quantity: 1, Year: 2010, Gas Fired, Width 2.0 mts, 6 Chambers, Pin & Clip, Kuster Padder, Mahlo Weft Straightener, Coating Head and Foam Generator, Excellent Condition Very Slightly used. Excellent Price to move.

Quantity: 1, Year: 2017
Special for PES and PES mixture fabrics after inkjet printing for color fixation., Model: NAT 1
Max. working width: 2.200 mm (installed conveyor belt is for 1.800 mm)
Heating system: Gas, Nr. of chambers: 4
Fabric entry: Bianco centering device with spreading roller
Exit :with plaiting device from Bianco
Condition: on Mill floor

Year: 2017
Roller width: 3400mm
Working width: 3200mm
Natural Gas Heated
Towel Weights: 400g/mt2

COMPOSED OF:
1 x High Capacity J-Scray for non stop operation

1st- 3 Bowl Padder with Stainless Steel Trough of 250 Liters
Squeezing Pressure: 12 Tons, Roller width: 3400mm, Working width: 3200mm

2nd- Bowl Padder for Application of Softner with Stainless Steel trough of 250 liters.
Pressing Capacity: 12 Tons, Roller width: 3400mm, Working width: 3200mm

FURNISHED BY:
Input Bridge with Centralizer Haul Bucket Bath with Discharge Valve.
Inside roller bucket device for adjustment speed switch stop start.
Electric and Pneumatic control panel.
Roller recovered by special rubber of high squeezing and convex rectified.

1 x TURBANG TSE-HP-PLUS for Towel of 3200mm usable width working with heating equipment for gas.
Automatic Filter for Fiber and Thick Dust. Output with Plaiter.

1 x TURBANG DRYING AND FINISHING MACHINE
Model: TMS MULTI-STRIKE-THREE

GENERAL SPECIFICATIONS:
Nominal Thermic Power……..750kw
Nominal Electric Power…….169kw
Electric Power: 380v, 50hz
Electric Voltage Control: 220V 50Hz

THE MACHINE IS COMPOSED OF:
Input Bridge and Input rollers driven by motor reducer group.
Main body of machine with compact structure.
Housing compartments for fabric with control system for quantity of fabric per electronically system.

MULTI STRIKE devices
Automatic filters with device for aspirating the waste accumulated on the surface of the filter.
Main ventilator for driving air propellant of fabric, with motor driven by frequency changer.
Fabric propellent system composed of special propelling pipes, air reversion butterfly valves.

Centering device at exit driven by reducer group.
Outlet with cooling system for Fabric.
Pneumatic Fabric guiders controlled by Optoelectric Sensors.
Complete electric control panel.

Quantity: 1, Year: 1998, Width 2000 mm., w.width 1800 mm., 2 compartments, Gas heating.

1 X Benninger Pad Dry Thermosol:
Year: 2003, Working Width 3200, Fabric Speed 30 -150 m/min

1 X Bruckner Curing Machine:
Year: 2005, Fabric Width 3200, 2 Chamber, Max. Temperature 210’C, Fabric Speed max. 80 m/min, Dryer Heating System Circulating Oil

Quantity: 1, Year: 2005, w.w. 2.40 m, 2 chambers, gas, vertical chain pin + clapets, padder and racla, Exit by book and roll.

Quantity: 1, Year: 1999, w.w. 3.20 m, gas