Quantity: 1, Year: 1981, 2-swift, Galaxy, ww 2.200 mm, 112 good ends, with shutfeeder, hopper feeder, Microweight scale year 2000, maincylinder dia. 1.500 mm, doffer 1.250 mm, all rollers with rigid wires in very good condition, 3 years old, Peralta, double apron condenser, safety guards with special electric control year 2015.
The machine can produce counts Nm 2-7.
Production naturally depends on the yarn count and is around 50-80 kg/hour.
The machine is in very good condition, in production.

QUANTITY: 1, YEAR: 2015, MODEL NSC ERA. , FEEDING 24 ENDS DELIVERY 1 CAN 700X1000 THE, MACHINE IS RUNNING

Quantity: 1, Year: 1986, Type GALAXY
width 2.50 m, feeding device with Servolap, 1 Cylinder dia 1.20m, 1 Cylinder dia 1.50 m, Peralta, 1 Cylinder dia 1.50 m, 1 Cylinder dia 1.20, double rubbing belt, delivery with 128 yarns, Apron draft (64) width 19 mm. Machine can be loaded into 3 containers.
Payment : 25 % at the order 75 % before starting the dismantling.
Machine was used for typical carpet yarns, for example:
Depending on the material and operator , machine can produce
a blend of 70/30 wool / Nylon
70-100 mm 34-37 Micron
Capacity To produce Nm range 3,2 is 400-500 kg/7.5 hour.
If necessary there is also in the factory a good spinning frame HDB ring dia 127 mm.
Machine’s quality is good but not perfect (8 out of 10 rating of quality)
Ctrs requirements:
Carding: 3 Ctrs
Spinning (if customer wants to buy) : 2 Ctrs
Reason for selling: They stopped production

1x HDB Card, 80” wide, consisting of:
A) 72” Wide Extended Apron Feed, 92” long
B) Feed Hooper, with a conveyor
C) Condensor
D) Feed Apron
E) 1 – HDB Card, Model Galaxy 2000
1st section is 2 cylinders, 80” wide, each cylinder has workers and strippers, v-belt drive, with Peralter, feed apron, with crosslapper which feeds the web onto a lattice apron, then goes to the 2nd set of 2 cylinders, 80” wide, with workers and strippers, with tape condensor, which has 168 ends, takes 12 spools, each spool has 14 ends, each spool is 40” wide Card #4, year 1996.

2x Gaudino Spinning Frames
Year: 1996, Model FB, Each is 252 spindles, ring frame, 90mm ring, 4” gauge, 14” bobbin, has a double drafting, automatic doff, each spinning frame has overhead cleaner, 2 draft zones, after the 1st draft zone it goes through a nozzle with air and has a twisting facility for the number of turns, then goes onto another drafting zone and then on to the spinning bobbin.

LINKED TO:
1x Schlafhorst Autoconer
Year: 1996, 24 spindles, with a TK760DAC slub catcher, air splicing, takes an empty bobbin and doffs them onto a 9” cone, with (2) doffers per unit, with length measuring , Model 147-0696-4066.
Currently the spinning frames and winder are running but the card is not

1-tape configuration – every 4 ends share 1 endless tape, they alternate in order similar to a figure 8
2- number of workers per section- 5,5,7,7
3- current working count range= 51.7-310tex, this could be expanded more
4-confirm condenser rubbing- each bank has 2 sets of aprons
5-feed type-servolap controlled with x-ray generator,reads density of fiber bed that controls feed roll speed
6-machine lockout system operational- this machine was fully operational until it was stopped.

Estimated 12 containers.

For production of tops, composed by:

Fiber preparation and feeding
1x OTR ROLANDO type RV1, year 2009, composed by:
manual feeding table connected to a vertical step cleaner, which connected with hopper feeder to the manual table with inbuilt fiber opener on the top.
After opening, opened wool forwarded to Rolando oil station and after oiling is delivered to the storage (built in company of isolation sandwich panel).

Carding section
1x THIBEAU NSC CARD TYPE CA6, year 1992:
ww 2500 mm., renewed and totally rebuilt in 2009, feeding silos with volumetric hopper feeder type ATM THIBEAU, 3 x morrel unit for burr removal, automatic can change dia. 700×1.200 mm. Card has low running hours, new wires working 21-22 micron wool.

Gills section
3x NSC SCHLUMBERGER gills type GC 15, year 2009:
combing zone 265 mm., creel 8 cans, delivery 1 sliver in 1 can dia. 1000×1200 mm.

1x NSC SCHLUMBERGER gill type GC 15, year 2009:
creel 6 cans (3 each side), feeding coming from combers, delivery 1 sliver in 1 ball.

Combing section
4x NSC SCHLUMBERGER combers type ERA-LM, year 2010:
creel 24 couplings, delivery 1 sliver in 1 can dia. 1200×1200 mm. No centralized suction.

1x GUALCHIERANI vertical hydraulic bale press type FTC200, year 1998:
pressure 200 tons, capacity 48 bumps (approx 10 kilos each) x 4000 mm., bale size of 1600x1100x800 mm., weight of 480 kilos each, manual strapping, height of 8500 mm, base of 550 mm. 46 cans (16 x dia. 1100 mm. and 30 x dia. 1200 mm.)

Accessories and existing spare parts
The machines were bought in year 2009 and were installed in year 2010
REGULAR MAINTENANCE
IMMEDIATE DELIVERY

NOTE: For sale as complete line.