AG47/050424E/OA-T/M/
Dilo OUG II 25 Finishing Needle Loom
Quantity: 1, Year: 1988, With CBF, with winder, ww: 2.5 m, Double board downstroke, Double board upstroke, 16 000 needles/m, 1 300 rpm.
AG47/050424E/TA-T/M/
Autefa Cross Lapper
Quantity: 1, Year: 1989, Controls from 2016, Input: 2.5 m, output: 2.5 m.
AG47/290324E/OO-O/M/
Spinnbau Double Doffer Card
Quantity: 1, Year: 1986, ww: 2.5 m, Avantrain + 1 swift, randomizing cylinders, up to 400 kg/h.
AG47/080324E/OA-T/M/
Santex Santatherm Thermobonding Oven
Quantity: 1, Year: 1995, ww: 4.5 m, double belt, 2 burners, calender, cutting and winding unit
AG47/080324E/ARI-AI/M/
Needling Line
Year: 1987
With upgraded electronics, ww: 4 m
Consisting of:
2x Hergeth Hollingsworth bale openers, ww: 1 m
1x Bonino bale opener, ww: 700 mm
1x Thibeau double doffer card, ww: 2.4 m
1x Asselin cross-lapper, input: 2.9 m, output: 4 m
1x Asselin DF 1 500 pre-needle loom (drum tacker), ww: 4 m
1x Asselin SD 41 finishing needle loom, ww: 4.1 m, double board downstroke, 5 600 needles/m
1x Asselin DF 41 finishing needle loom, ww: 4.1 m, double board downstroke, double board upstroke, 11 200 needles/m
1x Cutting and winding unit
AG47/080324E/AIR-P/M/
Needling Line
Year: 1982-1995
With upgraded electronics, ww: 2.2 m
Consisting of:
2x Laroche bale openers, yoc: 1994, ww: 1.5 m
1x Laroche pre-opener, yoc: 1994, ww: 1 m
1x Tatham double doffer card, yoc: 1982, ww: 2.8 m
1x Tatham cross-lapper, input: 2.8 m, output: 2.2 m
1x Asselin 169 pre-needle loom (drum tacker), ww: 2.2 m
1x Fehrer NL 9/S pre-needle loom, yoc: 1995, ww: 2.2 m, single board downstroke, 5 181 needles/m
1x Fehrer NL 21/R finishing needle loom, yoc: 1982, ww: 2.2 m, double board upstroke, 14 000 needles/m
1x Fehrer NL 21/R finishing needle loom, yoc: 1984, ww: 2.2 m, double board downstroke, 10 000 needles/m
1x Cutting and winding unit

AG47/080324E/AOS-AY/M/
Needling Line
Year: 1991-2006
With upgraded electronics, ww: 4.7 m
Consisting of:
3x Masias bale openers, yoc: 1998, ww: 1.5 m
1x Masias fine opener, yoc: 1998, ww: 1.6 m
1x Masias double doffer card, yoc: 1991, ww: 2.8 m
1x Asselin cross-lapper, yoc: 1991, input: 2.8 m, output: 4.7 m
1x Karl Mayer Malivlies stitch-bonding machine, yoc: 2005, ww: 5 m
1x Asselin SD 47 pre-needle loom, with batt feeding system, yoc: 1995, ww: 4.7 m, single board downstroke, 5 106 needles/m
1x Asselin SM 47 finishing needle loom, yoc: 1995, ww: 4.7 m, double board upstroke, 8 714 needles/m
1x Asselin DF 47 finishing needle loom, yoc: 1995, ww: 4.7 m, double board downstroke, double board upstroke, 17 429 needles/m
1x Bombi double cylinder thermobonding calender, yoc: 2006, ww: 5 m
1x Cutting and winding unit
1x Laroche edge trim opener
AF14/070324E/CT-R/M/
Dilo Pre Needling
QUANTITY: 1, YEAR: 1980/82, MOD. NFZ25, W.W. MM. 2500, WITH 2580 NEEDLES /ML, COMPLETE WITH MOBILE STRIPPING PLATE, SUITABLE FOR PRODUCT UNTIL 1500/GR – m2 and /or VOLUMINOUSE FIBERS, MACHINE WELL MAINTAINED AND IN GOOD CONDITIONS.
AG82/040324/
New Dilo Exccentric unit
The Unit has 60 mm stroke and is brand new.
It´s prepared for central lubrication system.
The eccentric unit is originally packed.
AG47/010324E/CC-R/M/
Tecnica Tessile Cross-Lapper
Quantity: 1, Year: 1990, Input: 2.5 m, output: 3.3 m, Up to 45 m/min.
AG47/010324E/YS-Y/M/
Trutzschler Opening Line
Year: 1983, Consisting of: 4 Trutzschler MWS bale openers, 1 Trutzschler mixing opener.
AB34/010324/BY/
Kusters Calender
Quantity: 1
Year: 1985
used 3 rolls thermobonding calender
Working width: 3200 mm, type 413.50, Machine/order number 10 62 470 4
Nominal width: 3700 mm, fabrics width: 3500 mm / conversion to 3200 mm
Total force: 555 kN, Line force: 150 N/mm, production speed: 10-150 m/min
Roller equipment:
1 swimming roller Kusters (S-roller); 1 Racolan; 1 steel roller
Technical documentation and electrical documents available
Special feature: Heat exchanger is part of the scope of delivery.
Electric heater no longer active, so conversion to heating via external thermal oil system (not included)
Ready for operation, line in very good technical condition
AA02/270224/
Wider Width Geotextile Equipment
BLENDING:
5x HOLLINGSWORTH 60″ WIDE FEED HOPPERS
TYPE: BFC-1500, 60 inch wide feed Aprons, Weigh Pans Empty Into a 40″ Wide Blending Conveyor, Year 1993
1x HUMP MAGNET METAL DETECTOR
Year 1990
1x SIGNAL MIXING BIN
100 inch wide, 250 inch long, Moving lattice steel floor for emptying, Inclined Lattice, Year 2006
1x TEMAFA MIXED FIBER BALE OPENER
60 inches wide, Main Cylinder with claw teeth, Feed roller with claw teeth, Double take off rollers with Claw teeth, YEAR 1998
1x ARGUS METAL DETECTOR
Year 1998
5.5 METER DILO LINE – YEAR OF MANUFACTURE 1998
CARDING:
1x SPINNBAU 3.0 M WIDE CARD FEEDER
With Air Box – Condenser, Vibra Feed Chute Feed with Feed Rolls
1x SPINNBAU WEIGHING TABLE
Type ME-Z
1x SPINNBAU SINGLE CYLINDER CARD
3 meters wide, Double Doffer, with Feed Rolls, Breast With Worker and Stripper, Main Cylinder with 5 Sets of Workers and Strippers, Double Doffers, Take down Aprons to Deliver Batt to Entry Apron of Crosslapper, Year 1998
CROSSLAPPER:
1x AUTEFA CROSSLAPPER
Model “Topliner”, Type 96.48, 3 meter Input, 6.0 meter Wide output, onto Floor Apron, Year 2012
NEEDLING:
1x DILO FEED, Model VE.4-60, Year 1998
1x DILO PRE-NEEDLE LOOM
Type: Di-Loom OD-1-S-60, 1 Board Down stroke, Compressive Batt Feed Type CBF-60T, 6.0 m Wide, Year 1998
1x DILO 4-ROLL DRAFTING UNIT
Type VE4/60, 6.0 meter Wide, Year 1998
1x DILO “QUAD-PUNCH” NEEDLE LOOM
2 Boards Down and 2 Boards Up Stroke, Type Di-Loom OUGIIS/55, 5.5m Wide, Year 1998
(1) Graseby (Goring-Kerr) Metal Detector
(1) Entec 4-Roll Stretching (Drafting) Unit
(1) Entec Inclined Pin Tenter
5.5 Meter Working Width, Vertical Chain Return, with Electronic Edge Guiding and Rotary Brush, Pinning On Device
1x HITRACH/ENTEC DRYER
with 10 Heaters and 2 Edge Heaters, with Circulating Fans, Hood and Exhaust Fans
1x PERKNS 4 ROLLER CALENDAR
Oile Heated with Thermal Oil Boiler
1x ENTEC VERTICAL ACCUMULATOR
with 144 Yards Linear Storage Capacity, NDC Thickness Scanner and Controller
1x ENTEC, FULL WIDTH LIGHTED INSPECTION FRAME
with Pull Rolls, with Edge Trim, and Automatic Edge Guiding on to (1) Entec 2 Roll Surface Drive, Automatic Tube Feeder, Take-Up Winder with Automatic Doffing
1x MACHADYNE ROLL-WRAPPING UNIT
with Traversing Wrap Unit, To Holding Table for Finished Rolls
1x RANGE DRIVE AND CONTROLS
To Operate and Monitor Entire Line, Type Di-Loom UD-II-SB 45, 4.5m Wide, Year 2006, Year 2013
ADDITIONAL EQUIPMENT:
1x P & S PICKER 48”
12 Bar Bear Claw
1x LAROCHE LOW MELT FINE OPENER
60” Width, Pin Beater Roll
1x THIBEAU CARD
Model 15P5 CA6, Single Cylinder, Double Doffer, 2.5 Meter Width
1x ASSELIN CROSSLAPPER
4.5 Meter Laydown, W/Floor Apron
1x VFW HOPPER FEED SYSTEM
1x THIBEAU CARD
Model 15P5, 2.5 Meter Width, Double Cylinder, Single Doffer
1x ASSELIN CROSSLAPPER
Type 390, 4.5 Meter Laydown, W/Floor Apron
1x FEHRER TACKER
Model NL9/S, 3.9 Meter, Year 1983
1x FEHRER NEEDLELOOM
Model NL21, 4 Meter Width, Year 1983
1x Argus Metal Detector
1x ASSELIN CROSSLAPPER
Type 390, 4.5 Meter Laydown, W/Floor Apron
1x FEHRER TACKER
Model NL9/S, 4 Meter, Year 1994
1x FEHRER NEEDLELOOM
Model NL21, 4 Meter Width, Year 1994
1x BOMBI THREE-ROLLER NONWOVEN CALENDER
Type CAL/3C/5.8, 3 Roll, Working width 5800 mm, Max roller width 6100 mm, Roller Diameter 800mm, Pressure approx. 25 tons, Oil Heated, Year: 2007
AG82/190224E/TA.L-T/M/AN/
Autefa Crosslapper
Quantity: 1, Year: 1996, Type: CL2003, Infeed width: 2.500 mm, Outlet width: 3.500 mm, Incl. control system, cabinet and panel, Spare parts, Cables, Well maintained. Max speed of the machine in m/min – 60-80 m/min, It is not a profiling cross lapper , Electronic control/ plc is available with the machine, incl. cables, Max gsm is not depending on cross lapper, Machine is stopped and dismantled.
AG82/190224E/YY.L-L/M/AN/
Autefa Crosslapper
Quantity: 1, Year: 1999, Type: CL2000, Working width: infeed: 2,5 m – exit: 2,5 m. incl. control system, cabinet and panel. Machine is connected to electrical power and can be seen running (without material), Max speed of the machine in m/min – 60 m/min, It is not a profiling cross lapper, Electronic control/ plc is available with the machine, incl. cables, Max gsm is not depending on cross lapper, Machine is working.
AA22/110224E/LPI-RI/F/AD/
Bematic/Bombi Random Airlay Line
Airlay materials find application in a wide range of industries due to their desirable properties, such as high porosity, breathability, and uniformity. The ability to tailor the composition and structure of airlay nonwoven materials makes them adaptable to specific performance requirements, making them an essential choice in diverse manufacturing applications.
Year: 2011
Width: 2500mm
Complete airlay line for production of automotive felt, construction insulation material, felt for mattresses and other applications. Max weight – 3000 gsm, line speed max 5 m/min, consisting of:
03 Bematic AC-1500 bale openers with feed tables and collecting belt, ww: 1500 mm.
01 Bematic SP-205 weighing tower, ww: 1500 mm.
01 Bematic AF-700 mixer/opener with transport fan, ww: 700 mm.
01 Bematic SF-1500 fine opener, ww: 1500 mm.
01 Bematic Bemablow feeder, ww: 2500 mm.
01 Bematic T-Max airlay former, ww: 2600 mm.
01 Bombi TFP/2N gasheated oven with 3 burners and cooling zone.
01 Bombi CAL/2C calender, ww: 2700 mm.
01 Bombi TG/2+2 length and cross cutter, ww: 2700 mm.
01 Bombi RAF winder, ww: 2500 mm.
Still running.
AG82/050224E/PO-O/M/AN/
Hergeth Hollingsworth Card
Quantity: 1, Year: 1988
Make: HERGETH HOLLINGSWORTH, Type: SSK, Working width: 2.500 mm
AG47/020224E/AS-R/M/
Dilo NFZ 30 DO Pre-Needle Loom
Quantity: 1, Year: 1970s, ww: 3 m, single board downstroke, 5 160 needles/m
AG47/020224E/AS-R/M/
Dilo NFZ 25 Pre-Needle Loom
Quantity: 1, Year: 1970s, ww: 2.5 m, single board downstroke, 2 580 needles/m
AG47/020224E/CAL-AL/M/
Needling Line
Year: 1975-2015, electronics from 2015, ww: 4.5 m
Consisting of:
1 Thibeau double doffer card, yoc; 1982, ww: 2.5 m, avantrain+2 swifts
1 Automatex cross-lapper, input: 2.5 m, output: 5 m, up to 45 m/min
1 HDB pre-needle loom, yoc: 1975, ww: 4.5 m, double board downstroke, 5 000 needles/m, 400 rpm
1 Bombi double cylinder thermobonding calender, yoc: 2015, ww: 4.5 m
1 cutting and winding unit
Up to 500 kg/h
AG47/240124E/PO-O/M/
Bonino Double Doffer Card
Quantity: 1, Year: 1990, ww: 2.5 m, 1 swift, condensing cylinder
AA22/180124D/ACT-AT/F/CI/
Bombi Calender
Quantity: 1, Year: 1998, Type: CAL 2C/5.7, Width: 5700mm, Two hard chromed and polished rollers (dia 700 mm), max pressure 20 t with air pistons, min. gap 0,14 mm, max opening 60 mm, felt thickness max 20 mm, speed: 1.2m/min to 12 m/min, max temp 260 C, yoc: 1998 including oil boiler.